Other

- Compatible with Shimano, SRAM, Campagnolo and KMC 11 speed chains - DLC Coated - Non-reusable - Opening Tool Required - Card of 2 pairs

The tool-free Maxle Ultimate Front brings exceptional stiffness and durability to your ride in a high clamping force, easiest-to-use internal cam thru-axle system.

The Problem Solvers Handlebar Clamp Shim allows you to fit almost any handlebars in almost any stem. It's machined of light and durable aluminum and grooved on the inside to hold tightly.

The Problem Solvers Cassette Spacers are made of light and durable anodized aluminum and come in different thicknesses for correctly spacing various brand and model cassette cogs. Measure and match your spacers to choose the right width.

Vuka Alumina Clip Risers are designed for use with the Vuka Alumina Clip's above-bar option. The risers are designed to offer a wider range of adjustability within the Vuka Alumina aero-cockpit system.

The tool-free Maxle Lite brings exceptional stiffness and durability to your fork in a light, easiest-to-use expanding wedge thru-axle system. - Thread Length: 9mm - Thread Pitch: 15 x 1.5mm

Surly wants you to be able to set up you ride just the way you want it. This pair of adapter washers make it so you can throw your favorite 135, 170, or 190mm O.L.D. 10mm solid axle hub into the rear end of a 142, 177, or 197mm spaced thru-axle frame. Add the adapters, add the wheel, install and tighten the nuts and, bam, you're ready to rip. Make sure the solid axle on your wheel is the right length for the frame spacing. For instance: 190mm OLD QR goes with 197mm thru-axle spacing.

- Powermeter Crank Arm Bolt Kit and AXS Cover Plug Drive Side M18/M30 Dub Steel Black Rival D1

- Grade 10 chromium steel balls

ReMatch adapters are designed to integrate different generations of Shimano Brakes to Shimano Shifters. Rematch Adapter 1.1 connects Shimano I-Spec A/B shifter to I-Spec II brake. - Made from CNC Machined T6061 Aluminum - Anodized Black - No additional hardware needed ReMatch 1.1 is NOT compatible with Deore M610 or SLX M670 shifters

Whether for derailleur clamp clearance, tire clearance, or personal preference, sometimes it can be advantageous to run the wheel further back in the dropouts. Monkey Nuts install into Surly horizontal dropouts to make spacing the wheel back easy. There are 3 different sets depending on the type of dropout and axle configuration the dropout is intended for. Simply select the correct version of Monkey Nut, install it into the frame, and slam the wheel all the way forward. Bang, done.

Rated fully KICKASS by a very authoritative entity who will remain unnamed, Surly's cast and polished stainless steel clamps won't rust or chip paint because they can't (even the black ones!). They're shiny! They look good! And most importantly, they deliver the clampability seatposts crave.

Thin, durable clear chainstay protector with extra-strong adhesive. - Overall length - 10.375

- Alloy construction - Great for Cruiser or BMX bar conversions

- SRAM, Road pulleys, 11.7515.060.000

The Problem Solvers Single Chainring Bolts include 5 chainring bolts and nuts that are 6mm wide. This is the right size for most single-chainring setups. These chainring bolts are made of either aluminum, stainless steel, or chromoly.

Replacement swing plates for Alternator 1.0 dropouts.

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Sport brake housing packs high performance features into a colorful and durable package, making it a functional and aesthetic upgrade. - Slick-Lube lined housing reduces friction for faster cable movement and better braking response - High carbon internal steel coil for improved stiffness - Appropriate for Teflon coated cables as well as steel and galvanized - Length: 10m

Air Can Assemblies for repair and maintenance of Rockshox rear shocks.

Internal components for servicing the Reverb and Reverb Stealth mechanism.

KMC Missing Link connectors are for use on new chains or to keep in your seat bag for an emergency repairs. - Compatible with KMC K710 and K710SL chains - No tools needed

Replacement top caps for various RockShox suspension forks.

CAMO Chainring Bolt Kit are designed specifically for use with CAMO spiders and rings - Includes 5 Torx head M5 x 8mm bolts - ED coated steel is durable - Bolts include a blue Nylok patch for a secure installation - Torque bolts only to 4-5 Nm and use blue Loctite threadlock

KMC Missing Link connectors are for use on new chains or to keep in your seat bag for an emergency repairs. - Compatible with KMC and Shimano 10-speed chains - Includes 2 pairs

Replacement elastomers for Thudbuster LT suspension seatposts allow the rider to tune for weight.

Wheels Manufacturing's SRAM compatible Universal Derailleur Hanger simplifies thousands of hanger designs into one universal standard. Machined completely out of aluminum, this new hanger is not only strong but designed to rotate backward and slip slightly in the case of an impact preventing chain jams and protecting the drive train. All Wheels Manufacturing replacement derailleur hangers are produced in our Colorado shop to exacting tolerances. - Compatible with bike frames designed to accept the SRAM UDH (Universal Derailleur Hanger) - Compatible with all MTB and eMTB drivetrains - Machined aluminum body anodized black - Thru-Axle thread pitch M12 x 1

Damper IFP Bodies for repair and maintenance of Rockshox rear shocks.

These 6mm long bolts are designed for single chainrings that have non-threaded standoffs. Uses a double hex head interface so you don't have to use a chainring nut spanner. - 6mm length - Made in the US out of 7075-T6 Aluminum - Has hex heads on both the bolt and nut for easy installation - Max torque of 7-8 Nm with light grease on threads only

Add some color and style to your bike build with Precision Headset Stack spacers. Offered in multiple sizes, made proudly in Minneapolis, MN, and laser marked with the stack size on each end, find your perfect fit. - Designed and manufactured in the Minneapolis, MN USA - Fits 1 1/8" steerers only - Made from 6061-T6 Aluminum

This stem cap is where your bike fashion sense and the weight weenie in you collide. This Ultralight and ultra-sleek stem cap integrates a 5mm, 10mm or 15mm headset spacer with your stem cap in finely machined piece. Why have extra steerer tube requiring spacers on top of your stem you ask? Well, many carbon steerers require that the steer tube extend above the stem. Also, riders may want the flexibility to move handlebar height up and down for different types of riding or for bike re-sale. - Design and manufactured in Minneapolis, MN USA - 1 1/8" top (straight 1 1/8" or 1 1/2" to 1 1/8" taper) steerer tubes only - 6061-T6 aluminum - 5mm internal cylinder wall height - Black aluminum bolt included Total weight (cap + bolt): 5mm= 12g. Compare to a standard flat stem cap and steel bolt at 20 grams + spacers add even more.

Tight tolerances and precise torque specs mean precision parts like this MegaExo 12 Left Arm Crank Bolt need to be replaced from time to time. Make sure the heart of your drivetrain is secure, and pick up a spare or two today.

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 30mm - Outer Diameter: 42mm - Width: 7mm

Parts for servicing Highline dropper seatposts. Kit includes: - Igus guide blocks x2 - Upper Igus bearing x1 - Lower Igus bearing x1 - Seal/collar assembly x1 - Grease packet x1 Compatibility: - All 1st Gen and 2nd Gen Highline Highline 3 & 7

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

38 Air Shaft Assembly for Fox suspension forks.

RockShox's Maxle Lite is a lightweight aluminum through-axle system. It lets you remove and install your wheel as fast as with a standard quick-release while delivering the awesome stiffness with the improved strength and control of a through-axle. Plus, the lever can be closed in whatever position you like and no tools are required for installation and use!

RockShox All Travel Spacer

Replacement compression knobs for RockShox suspension forks.

If you put in a lot of miles and/or sweat a lot, your shifter hoods probably need freshening up. Grab a pair of Shimano Di2 STI Lever Hoods to make your bike feel new again. - Fits Dura-Ace ST-9150 Di2 levers

Shimano's Di2 electric drivetrain takes shifting to the next level. Two Di2 Battery Chargers are available. Choose the model designed for your system's battery. An additional power cable is required for the external-style battery charger (sold separately). These chargers fully charge the battery in 90 minutes.

Keep the cable fixed securely in your Dura-Ace R9100 rear derailleur with this Shimano Rear Derailleur Cable Anchor Assembly

- Replacement chain pin for 7- and 8-speed Shimano chains - 3 replacement pins per pack

- Replacement pins for 9-speed Shimano chains - Compatible with CN-7700/HG92 chains - 3 replacement pins per pack

Get your scratched Shimano Dura-Ace shifters looking new again with these replacement name plates. They're perfect for sprucing up a well-used bike or erasing the marks of a crash.

- Lighter, XTR-grade caliper adapters - Includes conical washer for better caliper alignment - Works with all post mount calipers Legend : SM-MA90-F203S/P : - Position : - F: Front - R: Rear - 203 : Rotor size Caliper type: - S: Int-A-standard - P: Post Suspension/frame type: - S: Int-A-standard - P: Post - B: Boxxer - Z: Marzocchi 20mm

- Internal junction-A with two e-Tube ports - Externally facing charging port eases charging, especially for internal batteries - Mounts in road bar end or in frames with an integrated mounting point - For easier cable routing, use along with EW-JC130 three-way e-Tube cable

- EW-WU111 D-Fly wireless transmitter - Shifting customization, system diagnosis and firmware updates can now be done through Bluetooth Smart on smart phones and tablets, using the eTube app - Also allows to send shifting and system data to compatible cycle computers via private ANT+ protocol - Requires BT-DN110 internal battery or BM-DN100 external battery mount

The Maxle Stealth offers a light, low-profile, tooled alternative to Maxle Lite. - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

RockShox Volume Reducer Kits

DPX2 Damper Shaft for FOX suspension service and repair. - FOX Damper Shaft - Steel, DPX2, 2pc, 0.360 ID, 0.498 OD, 3.070 TLG, 210/185X 55/50

Chris King Threadfit Bottom Bracket Conversions to mate your King ThreadFit BB to your chosen frame and crank spindle.

Chris King bottom bracket Fit Kits for DUB cranks are used with Chris King bottom brackets to ensure that cranks mate perfectly with bearings, extend product life, and reduce the potential for noise. Fit Kits will also allow you to use one bottom bracket with a wide array of cranks, if you happen to change you cranks in the future.

Chris King bottom bracket Fit Kits for DUB cranks are used with Chris King bottom brackets to ensure that cranks mate perfectly with bearings, extend product life, and reduce the potential for noise. Fit Kits will also allow you to use one bottom bracket with a wide array of cranks, if you happen to change you cranks in the future.

Rival eTap AXS Rear Derailleur Pulley Kit - Steel bearings - Includes 12T upper and 12T lower pulleys - 18.5mm and 12.9mm steel pulley screws

Our mounts are all CNC machined to offer precise fitting to most frames and forks. KEY FEATURES - We hold a wide selection of caliper mounts to fit perfectly with our brake systems - Most of our mounts are available in a choice of black or silver - Brake mounts are machined from T6 2014 alloy - We have designed the brackets only for the purpose stated - All mounts are supplied with bolts for mounting to frame/fork *NOTE: Will not work with most Post Mount Marzocchi forks* - Weight from: 20g - All mounts come with bolts to fit to fork/frame - A wide selection to fit most combinations - CNC machined

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (1) M8 Chainring Bolt Note: Same hanger as Wheels Mfg DROPOUT-6.

Dimension Seatpost Binder Bolts - 16g

Bottom bracket cup and spindle spacers for adjusting chainline or bearing play.